Airaid Cold Air Intake System
- Wide-open airflow to your engine provides huge horsepower and torque
- Custom designed to fit your specific make, model and year vehicle
- Installs in about 30 minutes with household tools
- Available with and without Airaid's crosslink nylon intake tube
- All kits include a reusable air filter, in either SynthaMax (dry) or SynthaFlow (oiled) designs.
- 49-state street legal (not in California)
- Lifetime Warranty
Oxygen is essential to your vehicle's performance. Without air your engine is just a hunk of metal sitting in your driveway. And the more air you feed your engine, the better it performs. That's where the Airaid Cold Air Intake System comes in.
The Airaid Cold Air Intake System is custom designed for your vehicle to provide far more air flow than your stock intake. With up to 20% more air flow comes up to 20 more horsepower, up to 20 lbs. more torque, and maybe even improved gas mileage.
Depending on your vehicle, you may choose an intake with Airaid's mandrel-formed crosslink nylon intake tube. This tube is powdercoated on the inside and outside for great protection from the elements as well as improved air flow and looks. You may also choose an intake that bolts to your stock inlet tube. All Airaid Intake Systems include Airaid's own high-flow filter, in either oiled SynthaFlow or dry SynthaMax designs. Each filter is washable, re-useable, and will last as long as your vehicle does.
Your Airaid Cold Air Intake System installs in half and hour or less. You don't need to do any cutting, drilling, or modifications. You'll barely even need to open the toolbox! Airaid backs your high-flow Cold Air Intake System with a Lifetime Warranty.
Note: Thanks to the Magnuson Moss Warranty Act: US Code - Title 15, Chapter 50, Sections 2301 - 2312, the factory warranty of your vehicle is protected by law, even after the addition of aftermarket parts.
Airaid Cold Air Intake System Customer Reviews
Overall Rating:
4.8 of 5Average Install Time: 30-60 minutes
Showing 10 of 42 reviews. See All Reviews.
2021-09-02
This cold air intake is the best upgrade I've made so far! I love the design and the easy install. I'd recommend this as a must have in your Charger! Thanks for the recommendation based on your website!
Install Time: 30-60 minutes
2021-07-22
Good product. Easy install.
Install Time: Under 30 minutes
2020-06-13
Great product. Very pleased!
Install Time: 30-60 minutes
2019-07-12
Very high quality. Perfect fit. The sound is awesome but not sure of overall performance yet. I’m sure it will be better than stock.
Install Time: 30-60 minutes
2019-06-28
Easy as pie to install. Looks great too. Hopefully the performance will be as good.
Install Time: 30-60 minutes
2018-05-30
The cold air intake fir well and was easy to install.
Install Time: 30-60 minutes
2017-08-30
I like it because it was easy to install in my Ridgeline but when you disconnect the negative from the battery make sure you have your radio and GPS codes or you will not be able to use both you'll be locked out if you have a Honda. It also makes my truck sound like the old days when to you had a big four barrel carburetor on it when you open it up.
Install Time: Under 30 minutes
2017-04-16
Looks awesome and super easy to install. I was a little disappointed on my truck (2007 Yukon) that the expensive MXP model I purchased didn't doesn't pull air from the factory location as well like it shows in the picture. It only pulls from the bottom tube, the front behind headlight & the open top. Maybe they did it on purpose but I think it should be open and it would perform better. I think it sounds like stock at idle and cruise but when you get in the throttle it sounds mean and has a great growl! Love the sound. Can't wait to install my LSA supercharger lol...
Install Time: 30-60 minutes
2016-01-19
A little more noise than expected. Easy to install. Haven't seen much of an improvement in power or fuel mileage as yet. If I ordered again I would go with the banks.
Install Time: Under 30 minutes
2016-01-11
I bought this with a throttle body spacer & a Borla exhaust. Compared to stock I can tell a difference. It's more responsive on the throttle when I punch it. I'm happy with the purchase.
Install Time: 1-2 hours
Showing 10 of 42 reviews. See All Reviews.