BakFlip F1 Tonneau Cover 772601

The Bak Flip F1 appears to be good quality. I purchased one for a 2013 Ridgeline. The good...panels are nice and have a non reflective black surface. The design appears to be fairly good. The bad... The two side rails that were delivered appeared to have been modified from some other model to fit the Ridgeline. The front mounting holes were improperly located and the rails had been hand cut out on the underside to fit over the rear sidewall near the tailgate. The problem is that it took much longer to clean up the rough edges and file out the front holes to fit, install/ emove several times. Also the otherwise powder coated rails were compromised. Also, there was not a proper seal for the center mounting screw and the drain tube coupling was missing on one side. It needs a rubber block to insert in the recess on the side to seal the rail. In addition, I had to purchase some counter sink screws, (6 and 8mm) x 2" long, for the middle and front mounts as the head on the provided screws was too high for the panel to fit between the two sides. However, it is installed, had one leak on the center side, used tape to seal it for now.

This is a great product. It is a water tight, strong and secure bed cover. I especially like the way it doesn't change the contours or body lines of my vehicle. It sits and seals inside of the truck bed instead of lapping over the top of the bed rails. I would definitely recommend it to friends or family.

This is a great cover. It looks fantastic on the vehicle, without changing the lines of the vehicle.

Delivered on time, installation was as easy as stated, looks great on 2013 Ridgeline. First trip back from Colorado to Kansas had rain on I-70 for 3 hours. Sad to say it leaked up in the corners by the cab, so I added a little silicone to hopefully correct this problem.

The cover is exactly what I expected, works well and is very sturdy. The installation was a breeze. Before I bought the cover I read a review that said the kit included a couple of self-threading screws but the directions do not tell you what to do with them. It was easy to see that they went into holes in the rails near the tailgate to support the rails. The bad news was the packaging appeared to have been opened and re-seal. The cover itself was well protected but the rails were tossed in loose along with some of the hardware. One small clip was broken on one rail and the drain tubes were missing. I contacted BAK by e-mail and they sent replacement parts immediately. I have had the cover about a month now and have mistakenly closed the tailgate onto the cover twice. There is a warning label on the under side of the cover reminding you to close the tailgate BEFORE closing the last section of the cover. I guess I would put a label on top of the cover also.

The product came well packaged and the directions were very clear. I had it installed in about 40 minutes. Great quality and fit.

The cover itself is fine, although I would have preferred similar screws to those in the original truck body instead of straight Philips. The fit appears to be good although there hasn't been any rain to check water tightness and it wasn't enough of a concern to take a hose to it. For us, the primary use is to keep snow out of the bed during the winter. A couple of words of instruction about pulling down on the cables on each side to unlatch the unit wouldn't have killed BAK to add. It's obvious once you see it but when you're trying to get it on the first time it doesn't come quickly to mind if you've never used one and just lifted the cover from the shipping foam to the rails and discovered they'd snapped in too far forward. The drain tubes seem relatively pointless. It remains to be seen how well the provided recess covers keep out moisture.

Shopping was easy. The description fit the product. Installation was smooth and took very little time. I could have used an extra set of hands when installing the bolts to the brackets through the cover. The cover looks great and living in Florida we have plenty of rains so far only a few drops made it through and a minor adjustment seems to have stopped even those.

Well made product, easy to install, looks great on truck, easy to open, versatile opening positions.

Product very easy to install..40 min. and I work slow...fits really nice and doesn't leak...seems really sturdy...looks really neat on my Ridgeline...the interior trunk comes up ~3/4 of the way...plenty high enough for access...the bed extender works fine, too...lots of compliments, already...so far, very satisfied.

I am extremely pleased with purchase of my BakFlip. Ordering was easy and fast. Shipment arrived in perfect condition. Installation instructions were inside folded cover which I didn't open until I was in the final stage on installation so I used internet printed instructions. Everything fit perfectly. Hardest part was removing the #50 star bolts which were Honda factory installed. (ended up using an Allen wrench with a pipe for a breaker bar). Gas mileage went from 17.6 mpg to 18.5 mpg on a 53 mile freeway trip at 70 mph after installation.

The cover looks great, wasn't too bad to install but the instructions were a little vague. I got better information online from the folks who had already done it. If you could lock it, I would have given it 5 stars.

BakFlip came quickly and in good condition. Was easy to install and works and looks great on my 2012 Honda Ridgeline!

God product with a fast install in under 30 minutes. Happy.

The cover takes minutes to install and is exactly as advertised. I am glad I made this choice.

After weeks and months of selective analysis of Tonneau Covers, the F1 Bakflip was selected. It offered the looks, security, and functionality I needed for my Ridgeline at a fraction of what the Dealers were asking for lessor quality and performance. The installation was a snap, but did need some helpful phone assistance. My daughter did not believe that I installed the Balflip myself!

Good quality, the F1 does what it states and then some!

Easy to install and great looking. I saved $300.00 on the install by doing it myself. Cool!

We are very satisfied with the BAK F1 Tonneau cover. It was easy to install, works well, looks great, and - best of all - doesn't leak!