MagnaFlow Exhaust System
- Regular Price: $428.50-6,043.75
- Our Price: $290.89 - 4,103.03
- Shipping:FREE SHIPPING
- Rating: (65)
- Magnaflow Exhaust Systems restore the full torque and horsepower potential of your engine
- Built from high-flow 409 Stainless Steel tubing
- Lower heat, higher exhaust scavenging, and minimized backpressure provide greater power and efficiency
- Included muffler(s) are designed for ideal temperature consistency and reduction of vibrations and harsh noise
- Available in single and dual kits, for gas and diesel
- Most systems come with polished Stainless Steel tip(s)
- High-quality, leak-free overlapped welds
- Bolt-on installation with simple hand tools
- Mounts at factory positions, 50-state smog legal
- Three different system types available, depending on vehicle:
-
- Magnaflow Series: Top-quality systems with polished muffler(s) and double-wall welded tip(s)
- XL Series: Mid-range systems with satin finish muffler(s) and single-walled clamp-on tip(s)
- Pro Series: Entry-level systems with stainless muffler(s) - tips sold separately
- All systems backed by a Lifetime Warranty
Bolt on a Magnaflow Exhaust System, and fasten your seat belt. Magnaflow's top-shelf 409 Stainless Steel exhaust systems give you significant power and performance gains, with a throaty growl and no annoying harsh noise. Plus, it bolts to factory locations to keep your ride 50-state street legal.
Whether you use your vehicle for ripping up the racetrack or hauling lumber to the job site, Magnaflow's Exhaust Systems bring you the performance you need. Expect substantial gains in horsepower (3-23 HP) and torque (6-28 lbs.) , as well as a better feel under the pedal. Magnaflow achieves this by using 20% less bends than your stock exhaust and utilizing mufflers with a steel mesh core that keeps an optimal temperature for ideal flow of exhaust gasses. As well, half-inch overlapping MIG welds in your MagnaFlow Exhaust System make for tight, leak-free seals on every joint. The mufflers come packed with dense sound-absorbing material to filter out the excessive noise and vibrations you get from other exhaust systems.
MagnaFlow custom exhaust systems are engineered to your specific year, make, and model, ensuring a perfect fit and fine-tuned performance for your gas or diesel vehicle. Your new MagnaFlow Exhaust bolts right up to your vehicle in 1-2 hours with no drilling, cutting, or welding, and maintains your emissions to stay 50-state smog legal. Most mufflers are mirror-finish polished stainless steel, and most kits include polished stainless exhaust tips for a slick finished look.
Magnaflow backs your performance Exhaust System with a Lifetime Warranty.
MagnaFlow Exhaust System Customer Reviews
Overall Rating:
4.8 of 5Average Install Time: 30-60 minutes
Showing 10 of 65 reviews. See All Reviews.
2019-05-04
I would have given it five stars across the board but the package was delivered to my home and I brought it to the mechanic shop. When they open the package there was no hardware. No hanger straps and no clamps. Just the pipes were in the sealed carton. The job would have taken about 40 minutes to complete but I had to wait over an hour for the missing parts to be purchased from the auto store and delivered. So the pipes are great, they look and sound great, but there was a serious lack of quality control in packaging.
Install Time: 1-2 hours
2019-01-27
This exhaust pairs perfect with Stage 3 intake manifold, Stage 2 Air intake and Tune upgrades I did. It gives a nice growl to the car but not obnoxiously loud to the point of setting off car alarms as you drive by. The hardest part is cutting off the stock exhaust as the clearance between the top of it and heat shield are minimal -see pic. I used a 6" cut off wheel on my angle grinder to cut off as much of the pipes as possible then used a hand hacksaw for the rest. Some Tips for the install: Marking the cuts: Lightly clamp the magnaflow pieces together then put it on jacks under car and align it to the hangers then mark the spot. Cutting stock one: If using 6" cutting wheel then start the cut between the two pipes and go up as far as possible then from that point cut outwards of each pipe. Removing/Installing old/new exhaust: Use jacks to hold in place and support the weight while doing either. Stock exhaust: weld a sleeve that extends roughly 6" before and after the end you cut off. Now you can swap between the two if needed (takes 10 mins to swap) or keep it as a backup. Follow the rest of the directions that come with the exhaust. Take your time and use neccessary safety equipment when doing this easy DIY. Autoaccessoriesgarage.com is a 5 Star place to shop online for the best deals that come with the best customer service I've seen in a long time. Disclaimer: This is NOT a paid review - This is from my personal experiences with the company. -The Coz
Install Time: 30-60 minutes
Installing soon. Superior customer service.
Install Time: 30-60 minutes
Good service and quality parts. Was kept informed and received the parts in good time. Would recommend and will use them again.
Install Time: 1-2 hours
2018-06-09
It looks great on and wasn't hard to install.
Install Time: 30-60 minutes
2018-04-25
Great sound, great look, feels like the vehicle is faster as well.
Install Time: 30-60 minutes
2018-04-16
This exhaust literally took 20 minutes to install! Easy install, looks great! Sounds even better. I would highly recommend this product to my friends.
Install Time: Under 30 minutes
2018-03-24
Very pleased with the magnaflow exhaust system. The exhaust system was very easy to install I was able to remove my stock exhaust and install the magnaflow system in about 1 hour.
Install Time: 30-60 minutes
2018-03-23
Nice sound, not too loud. I feel the power back. The only issue I had was the lack of an asbestos gasket missing from the parts. Overall, happy with price, quick delivery and quality of product.
Install Time: 30-60 minutes
2017-11-03
Exhaust kit fit on my 2011 RAM 2500 HD with the 6.7 L Cummins Diesel very well. All bends were in the appropriate places and the hangers lined right up with factory mounts. Only complaint is I have one joint that I cannot get to stay tight (the second joint past the DPF, just before going over the rear axle). The instructions indicate to make the bands very tight and to re-check the connections for tightness; after re-snugging the joints, that particular one begins to rattle after about 3 weeks despite tightening the band with an impact gun (eventually to the point the pipe began to crush). I will probably have to get the pipe welded to get it to stay.
Install Time: 30-60 minutes
Showing 10 of 65 reviews. See All Reviews.
