BakFlip MX4 Tonneau Cover 448203

Forward flange on side rails. Slots are not lined up to bolt holes. They are inboard about a 1/16th of an inch which leaves both in a cocked position. Foam pads against cab are too small in diameter and leaves the panels very close to rear window. I would make outboard foam bigger diameter and leave center the way it is to allow sliding window to operate.

Overall it went on pretty easy and am really happy with the quality and the look. I did have some issues with the back end sitting flush on my tailgate. After I adjusted it a few times I was able to tweak the back corner of the rail down which allowed it to close evenly across the tailgate.

Great product and easy to install!

Could use another set of side rail clamps and the instructions should include how to adjust the latches.

Very sturdy and love the looks!!

Love the cover, looks great and took me 40min to install, was very easy as the instructions were clear. The only down side was the passenger side corner by the window was broken not too bad and certainly not worth sending back as it took awhile to get, but overall very satisfied.

It went on well and looks good. I haven't tried a water test yet.

Overall the cover looks very nice and it looks like it’s good quality. Basically it was fairly easy to install until it came to the small details. The locking mechanism at rear by tail gate would not lock because the metal trim pieces around vinyl locking clips were getting caught on side rails. I had to file the trim pieces until they cleared the rails on each side which took quite a while to get right, if it weren’t for this I would rate 5 stars for your product. Overall I’m very satisfied but if you’re not handy with tools it would have probably been returned.

It not only looks good but very well constructed i am very pleased with it. I thought I ordered the flex fold box at the same time, if not I need one. Thank you.

Overall it took two days to complete the install. One of the side tracks was bent in transit which required time to resolve. Also some of the panels would not lie flat as the panels were incorrectly joined and required time to troubleshoot.The most time consuming part of the install was adding the drain tubes, as I already had a liner in the bed. These drain tubes were a suprise, didn't know these were part of the kit. Overall the cover performed well. Last Sunday we experienced 9.8 inches of rain from hurricane Eta, with only minor leakage.

Product was as expected. It would be better if each panel had a latching mechanism. Slight water leaking in near tailgate other than that test of bed was dry.

Love this product. Easy install. Perfect fit. Looks great.

Shipment came quickly. Easy install no complaints. Getting ready for a road test and get all my gear out of the garage and back in truck. Should have some rain later today, so we'll see how it seals.

Installed in about an hour and works great. Easy to install and no leaks or issues. Sturdy too and very easy to open and close with minimal work required. Highly recommended!

Fairly easy to install, definitely need a partner. My 17 year old son was impressed so it passed the coolness test. I would buy it again.

I can only review the initial install at this point. Fit was a bit tight. Had to relocate 4 latches to allow proper fit by redoing screws. Should have easier way to adjust. Had a lot of rain lately, and repels water good. Appearance is good.

Works great and install went quickly.

Easy to install. Good instructions. Looks and performs great.

Great product! Fit like a glove!

I was surprised that the clamps did not fit. They're actually well designed and clamp well, but as one side fits into the curve in the bottom of the bed rail and the other side fits in the top of the bed cover rail, this meant the bedcover rail would not sit down flush with the bed. I had to cut off about 3/8" from one side of the clamps. Aside from that, this looks to be a very well built cover and I like the way it can be opened by one person from either side of the bed. When folded, it takes up less space than I thought it would. I'd recommend you buy it, just be warned, you might need an angle grinder to install it.

Looks good and the customer service was good!

Love the cover, it is better when you follow their well written directions to a T.

What an easy install and great fit. I think it took longer to unbox and sort part to get ready than it did to install it. Love it at this point. Lets see now how it lasts.

First of all the customer service is awesome, second, I got my Truck bed cover (BakFlip MX4) in good shape, easy to install instruction included were precise. They just earned my repeat business and for sure I will recommend this store to friends and family.

Ordered online and received within 5 days. Great price and quality. asy to install. Perfect fit. Everything works as advertised and would buy it again.

I'm 69 years old with a bit of arthritis, so layin on my back in the bed was not to easy, but got it done. Followed the directions to the letter. Worked great.